Frequently Asked Questions WINDOWS the best solution

1, why the computer shut down automatically after restart? A: Computer shuts down automatically after the restart of the most common cause of the shutdown was caused by fast. Is a solution: ① enter into operation: msconfig utility to configure the system to determine the procedure to select high-level "Disable Fast Shutdown" to restart the computer. ② If you can not see if there is a hardware or driver error. Under normal computer shut down automatically when the resumption of the general board is due to problems caused by power management. Some of the main board power management components, due to wiring design and quality parts, on the level of response to the signal is not very accurate. As the board to cut off power supply in the moment will have a moment of high pressure, high-pressure existence of this very short time, hardware damage resulting from a very small role, but will usually card, modem, and other PCI devices have a slight pulse. To determine if there is no noise signal, and the BIOS of your motherboard to open the automatic wake-up function, the board will be detected by external devices such as network card to connect the request, then start automatically. This is due to rise to the hardware, the motherboard simply refresh BI0S not solve the problem. You can try to shut down in the BIOS on the motherboard features automatic wake-up try, but also in power management setupwake-up by pci carddisabled (closed pci card wake-up function). Note: If the computer automatically shut down, it should enter the BIOS, to check whether or not to open the automatic shutdown temperature control functions, it can be shut down or control the temperature increase, to prevent them from automatic shutdown. 2, a computer Why then automatically power on the boot? A: The reason is: ① Plug Power does not guarantee a good contact, ② computer power supply problems, ③ bios setting. Solution: ① plug repair, ② the replacement of computer power, ③ configuration bios: in powermanagement setup of pwron after pwfall in power after the calls were to choose the state on, off and former_sts a try. Q: My computer recently a host on its own electricity to start, do not press the button to start the host. After removing the keyboard, there is no power like this now. I for a new keyboard, but in such a situation. I do not know what went wrong? Answer: a power that is automatically activated, may be Power_Good power supply circuit board failure or RESET circuit failure. Recommendations for a good power to try. In other words, if, after power addressed is the question of power; if not solve, the problem is the motherboard can be sent to the supplier repair or replacement. Remove the keyboard system could not be activated because the system BIOS at startup automatically detects hardware configuration, if there is lack of hardware, will self-suspended, and lack of resolve, self-test in order to continue. 3, how to delete the browser's address bar of the web site? ① delete the address bar of all Web sites: click on the "start" and then → "settings" and then → "Control Panel" and then click → "Int - ernet", you will find that there is a "history" of the plate. There are "delete history," click on the oh. You can also tune in the address bar of history preserved. Note: enter the "Internet" a lot of ways! For example, on the desktop to open Internet Explorer to find the "tool" to enter "Internet Options." Internet Explorer also can be a method of election of right-click "Properties." ② to delete the specified address bar Web site: first, "start" and then click on "Run" enter history. Choose the right time, and then Check it out! Which will not delete any! ③ delete the Chinese Web site, in fact, is called "real-name network." It remains a deleted click on the "start" and then → "settings" and then → "Control Panel" and then click → Internet appears a window above to find the "senior" in the "real-name network" called "to clear the address bar drop-down list Shown in real-name networks, "click on the box in front of the line! 4, how to solve the windows can not fault shutdown? The computer can not automatically shut down power, but remain in the "can now turn off the computer security," the screen will not move. windows can not be shut down due to a combination of the solution are also different. ▲ point, "turn off the computer", the computer does not always respond, there is a solution: Due to the rapid use of the system shutdown mechanism, but also the rapid shutdown is not compatible with some hardware, you only need to disable fast shutdown, as follows: running "msconfig", and the pop-up menu, select "Advanced" Labels, select the "Disable Fast Shutdown" (or "Disable UDF file system" or "If the shutdown failed, disable the disk scanner"), established to restart the computer. As the result of high-level power management functions, the following methods can be shut down power management features: "Start / Settings / Control Panel / System / Device Manager / System / Advanced Power Management / set / clear the opening of the power management," according to the established , Restart the computer. As the file system caused by the conflict, such as: system.ini file or win.ini file conflict. You can start when they entered the protected mode, the conflict can not be certain as to the specific location, only by modifying the system files that may conflict, restart the computer after determining whether the normal, repeated the steps until the issue is resolved. ▲ windows shutdown "is now shut down" and keep this picture, since there is no response, the hot start null and void. There are solutions: First of all, use Microsoft System Configuration tool Msconfig.exe, check what procedures are run, clean the system and guide, if clean can lead to solve the problem, you can re-use system configuration tool for their own use each of the relevant procedures to determine the cause does not shut down Procedures. In addition, such as graphics or sound card device driver problems, but also caused the shutdown failure to frequently asked questions. Into the "Control Panel / System / Device Manager" tab, disable all devices, and then reboot the system, if the issue is resolved, one by one and then the opening of the device is disabled in order to find out whether or not a hardware issue failure led to the shutdown. If the above steps to determine the cause of hardware is a non-normal shutdown, the device should contact the agent to update the firmware or driver. To modify the registry: Run regedit, into the registry into hkey_local_machinesoftwaremicrosoftwindows ntcurrentversionwinlogon branch, in the right window to find or create a new type of reg_sz registry, as the name of "powerdownaftershutdown", double-click its value to 0 (0 to allow automatic power shut down, does not allow for an automatic power shut down). 5, how to solve the laptop to the LAN, but not on the Internet? May be due to the laptop's original computer local area network through a proxy server on the Internet; and the other computer is not a local area network through a proxy server on the Internet, so when the laptop to a local area network, after which only the local area network, Accessed the Internet. Solution: Right-click on the IE browser to connect to remove point-point attributes, "Use a proxy server" before the hook (that is, not elected "Use a proxy server") to determine. 6, how to download the flash animation on the page? All Internet sites visited, animation (including flash animation), are recorded and stored in C: WINDOWSTemporary Internet Files folder, therefore, as long as you are on a web page viewed on the web page flash animation, the folder in there flash animation, as long as copy it to another folder, you needed to have a flash animation. This shows that the Internet computer for a long time, the folder C: WINDOWSTemporary Internet Files are expected to grow, it is necessary to clear on a regular basis to ensure that sufficient hard disk space. 7, in their own web pages, links to other sites bulk provided by the "site links"? One approach: first to open other sites (pages) use the File menu microsoft frontpage editorial in the general view to choose the content of links to right-click Copy to view HTML code DW view, and in between the right-click to paste DW Design view, Amend. Second method: first to open other sites (pages) File menu to save the importation of pages of documents preserved. DW run to open the documents preserved by using copy and paste approach to their own web pages, links to other sites to provide bulk of the "Web site link." 8, why can not notebook projector to the projector? Desktop computer connected to the projector all the normal projection, however, notebook computer connected to the projector, there are two exceptions: a, the notebook LCD display screen, projector (screen) does not show information. Solution: This situation occurs because the boot sequence error. The projector is a computer peripherals, and computer peripherals to start with the correct sequence is peripheral to start, after your computer. Therefore, the solution is: first computer and peripheral connections, and then start the projector and finally to your computer (or restart your computer). Some notebook computers are also key conversion: + or F3>. b, the laptop LCD screen black (no display of information), but the projector (screen) to display information. Solution: This situation has arisen due to: a, no laptop at the same time liquid crystal display projector screen and peripheral functions; c, notebook computers and projectors are not compatible; c, for reasons unknown, pending the study. 9, how to open a secondary cache of the P4? My computer's CPU is a P4  Willamette  1.6GHz, UNIKA UP4X266A board, in AIDA32 tests, CPU in the discovery of L2 Cache show for the Disabled in PCMark The information system in 2002, the CPU of, L2 Cache as a guide when the show closed, I would like to ask how do I open the P4's L2 Cache? How can we know that L2 Cache is turned on? You encounter the phenomenon from the point of view, this is due to the BIOS to disable the secondary cache due to open a secondary cache is simple to use, into the motherboard BIOS, the "CPU Level 2 Cache "(or CPU External Cache) option is set to "Enable" can, and when set to "Disable" when it is disabled, to open in the secondary cache, you will be able to once again run AIDA32 verified. Some of the players in the limit when overclocking will be the closure of secondary cache, while the secondary cache can be disabled to improve the success rate of overclocking, but will also greatly reduce system performance. 10, how to find the missing input signs? Misoperation due to the normal shutdown or other reasons led to the taskbar on the input of the missing signs, at this time how this can be done? A: Generally speaking, we open the "Control Panel", "Input" dialog box, "start on the task bar indicator," a hook on the problem. However, in some cases to do so and there is no result, then we can try to modify the registry. First of all, run "regedit", to start "HKEY_CURRENT_USER \ keyboard \ preload" branch, at its next create a new string value named "1" and its corresponding key to "00000409." Finally, close the registry, restart the system will be able to. In addition, the system "internat.exe" document will lead to loss of the problem. We can learn from other computers in the same copy of a document, put it into Windows installation directory for the system if  Win2000/XP, into the installation directory System32 folder , and then started running  registry "HKEY_LOCAL_MACHINE \ Software \ Microsoft \ Windows \ CurrentVersion \ Run "branch in the right side of a new string value, the key value and key are replaced by" internat.exe ". Finally, close the registry, restart your system. 11, black screen displays the reason? Some time ago a computer with a large fan noise, then open the box to see the original card is the fan and power lines caused by friction, so the two separate, and graphics tools will be put, the noise vanished. A few days later but the boot of a sudden black screen display, to open a case, the card does not turn the fan. Thought it was broken to start the card can be normal for a piece of card, or black. I would like to ask why? A: The reason why such a failure may be due to the fan card with the power cord friction collision with each other, by repeatedly squeezing Goldfinger graphics board AGP slot in the metal contact chip, so that the metal piece appeared in permanent contact deformation . First of all, please double-check AGP slot on the motherboard inside the flexibility metallic contact film to see whether they are bending deformation, if any, clocks repairs with the use of stainless steel tweezers, one by one carefully adjusted until the normal test . Black screen display may be another reason for the old display does not support high-resolution frequency solutions into the windows to reduce the resolution. 12, full-duplex sound card in the windows xp why not within the next recording? Q: My computer's sound card is a full-duplex sound card, but why can not under windows xp with sound recording? The main reason for not recording a "sound volume control," not the right choice. The solution is: Annex entertainment program to start volume control options in the menu attribute recording volume control menu option under the "Stereo Mix" or "stereo mix." 13, how to retrieve the lost Word menu? May be due to the misoperation of the reasons, my word it's missing some of the menu, I can not set up line, how to find the missing menu? Answer: word of some of the default settings are stored in the Normal.dot template file, so long as the reconstruction of the document can be. Click the "start looking for a file or folder," in the pop-up dialog box, type Normal.dot, set the scope of the search in the district office where the installation files, click the "search" button, to search this document will be deleted. When the word re-start when the re-establishment of the document, and the default application parameters can be removed to restore the menu. 14, to see how the local IP address and MAC address? a, win98 under investigation Ip and MAC address of the way In the "start -> run", type winipcfg, the pop-up dialog box to display mac and ip address. b, win2k/winxp investigation under way ip and mac "Start -> -> Accessories -> Command Prompt" At the command prompt type ipconfig-all 15, restrictions on how the workers during working hours through the QQ online chatting? I have a unit of a local area network through the server to share Internet access ADSL, had been normal, the latest of a new network management, blame the problem on more, the following is the only workstation or QQ, other applications (such as Internet browsing) Can not be used, and sometimes they just can not use QQ, I do not know why? A: If the unit's local area network to share Internet access on the server is used like the Wingate proxy server software, such software can be of different agreements and disable the port, if the HTTP protocol is disabled, you can not lead to browse Access to the Internet, such as QQ and the software is used by the Socks 5 port if the port are prohibited, QQ will not be able to use, there are a lot of units to limit the working hours of workers in the Internet through QQ chat, Fengdiao the port. However, there are specialized software lets you break through a proxy server port some of the restrictions here do not go up. 16, is how to record movies, vcd screen? Q: recording the film is playing, vcd of the screen, players are crawling film, vcd screen, remote viewing is movies, vcd computer screen, the screen is black, not the content of the film, and why? A: This situation occurs because the windows in the video, in order to enhance the smooth and delicate images, hence the use of Microsoft's DirectX technology to enhance the quality of video images, the computer media player technology and content of the video window to let in the sub - The two images show floor does not make sense, in order to allow the window with the contents of the video recording at the same time be able to crawl, as long as the graphics hardware acceleration can be closed by: Right-click the desktop windows of the High Point property problems "hardware acceleration" To "Disable all hardware acceleration." 17, in the local area network within the on-line neighbors how to hide the computer? A: In the next win2000/xp There are two ways to achieve: 1, the registry editor. In the "HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServiceslanmanserverparameters" branch, new or modified "hiden" The key value of "1", the key is the type of dword. 2, in the command prompt window running "net config server / hidden: yes" to order. 18, in the local area network within the Internet how to solve the problem of exchange of visits between the neighbors? Q: winxp install computer win98/2000 and sometimes can not visit each other's computers, set up shared folders, not to solve the problems in the local area network within the Internet how to solve the problem of exchange of visits between the neighbors? A: winxp to address on-line neighbors to share the problem: (1) installation NWlink IPX / SPX / NetBIOS Compatible Transport Protocol agreement. (2) open a guest account: Right-click My Computer users manage to have a guest, double-click to remove the "disabled accounts" in front of the hook. (3), right-click My Computer properties of the computer to see the tab appears in the local area network working group name, such as "WORKGROUP" network ID to choose the next step "is a local business network, use it to connect to the other The computer "to choose the next step," the company did not use the Web domain, "then enter the working group of local area network, such as" WORKGROUP "to complete the next step. Restart your computer. (4) the use of winxp firewall exception: winxp firewall in a state default is fully opened, which means that running the computer network linking all, difficult to achieve on-line neighbors to share. At the same time, due to the default windows firewall is a ban on the "File and Printer Sharing", so that the firewall is enabled, they can not print sharing, the solution is: to enter the "local connection" window, "High", "set up" " Exceptions "in check procedures and services under the" File and Printer Sharing. " (5) to delete "from the network to refuse access to this computer" of the guest account: run the Group Policy (gpedit.msc) of the local computer to configure the computer to set security settings windows of the local strategy users from the network refused to assign the right to access to this computer. If there is one guest, will be deleted. (The reason is: xp sometimes the guest is not allowed to access shared) (6) the abolition of "the use of simple file-sharing": Explorer folder options to view a tool to remove the "use simple file sharing (Recommended)" in front of the hook. (7) Working Group on the same name. (8) Check the "Microsoft Network File and Printer Sharing." (9) run strategy "Services.msc". Start the "Clipbook Server "(folder server): This service allows you to other network users to see your folder. Sometimes, of course, you can start it manually changed, and then use other programs on your network to distribute information. (10) win98 computer win2000/winxp not be able to access the computer, because: win2000/winxp computer users in the guest is disabled or win2000/winxp use the NTFS format partition, set up permissions control. General win98 allowed to visit, then, win2000/winxp's security control, not everyone will be the group to remove Account. NOTE: a, If you do not join the domain and would like to view the "security" tab, then set up display "security" tab: Explorer folder options to view a tool to remove the "use simple file sharing (Recommended)" in front of the Hook. b, to view files and folders effective authority: Explorer right-click to view effective permissions of the file or folder "Properties" Click the "Security" tab "Advanced", "effective authority", "choice" in the "name" Box, type the name of the user or group, and then click "OK." Check that the selected user or group of files or folders on the effective authority. c, can only use the NTFS format for the drive to set permissions. (11) on-line neighbors is too slow to address ways: win98, do not assume that the network novell network compatible with deleted in order to novell netware network equipment ipx / spx compatible to the agreement; win2000/xp, the system could remove the letter documents and setting Nethood username folder to all documents. 19, how to treat the partition table? A: The partition table is damaged, start the system often "non-system disk or disk error, replace a key to reboot" (non-system disk or disk error), "error loading operating system" (into the guide dos Records of the error), "no rom basic, system halted" (not to enter rom basic, the system stops responding) message, and so on. Here's where the partition table: a, killing virus: kv3000 / k b, or use the fdisk command gdisk repair: fdisk / mbr or gdisk / mbr. c, through hard kv3000 ambulance Wang repair: kv3000 - f10. d, with kv3000 backup to restore the partition table: Back up your hard disk master boot record: kv3000 / b, Floppy disk will generate 2 files: hdpt.dat, hfboot.dat. Restoration of hard disk master boot record: kv3000/hdpt.dat. 20, how to solve the problem of missing NTLDR? How to solve the problem of missing NTLDR? I installed Windows 98 and Windows XP dual-system boot-up pop-up "NTLDR is missing ..." message, the system can not start, how? NTLDR is the Windows XP start-up is an important guiding document. The above message that your computer has been lost in the document, directly from other versions of the same system in the C disk or copy them directly from a Windows XP installation CD-ROM extracted from a store that you can intraday C, If the trouble directly to repair the installation of Windows XP can solve the problem. 21, where the windows xp why not open the letter? My computer system with three windows98, widows2000, windows xp were installed in the C, D, E set, usually the default e is the start of the disk windows xp. One day, through a smooth power-on self test, after which the screen black, boot repeatedly been the case. Later, with windows2000 boot, everything will be all right. However, access to my computer or Explorer, double-click the disk E, suggesting that the site could not be opened, why? Why is there such a phenomenon so far not understand why. I have explored repeatedly, the only ways to tackle it, at first, into the My Computer or Explorer, E wants to set high-level formatting, can not be carried out, had failed to resolve numerous times. Later, before using the backup to restore the gho, the boot is not successful. Finally, finally can be solved by: Boot into windows2000, into the control panel, computer management, disk management, the E disk format, ok, and then resume the previous backup gho, boot, everything will be all right. E may be due to a disk Bad Track. 22, USB keyboard in the Win98 pure DOS mode, can not use? I have a USB keyboard, the result of pure Win98 in DOS mode, can not be used in the normal use of Win98/2k/xp inside. How do? USB devices generally need to drive, because the keyboard is a USB keyboard, the first port USB drives, which can be carried out in the CMOS, CMOS general of integrated peripherals which have USB keyboard spupport / USB mouse spupport option to choose Keyborad it. Some board may choose to Enable or Disable for usb mouse and keyboard support. Enable set to be resolved. 23, how to improve the speed of the start-up windows xp? Answer: a. Do not look at the boot screen before Windows 98/Me, we can appear in the boot when the screen by pressing Esc key to cancel it, and Windows 2000/XP will have to open the BOOT.INI file in the multi (0) disk (0) partition (1) \ WINNT = "Microsoft Windows 2000 Professional" / fastdetect statement after the plus / NOGUIBOOT, which is multi (0) disk (0) rdisk (0) partition (1) \ WINNT = "Microsoft Windows 2000 Professional target = "_blank"> disappeared on the surface, the speed will start a slight upgrade. b. on the Windows XP start for optimization Windows XP has a good new features, that is, when can start Disk Defragmenter, so that those who start the necessary documents can be arranged in adjacent, so that the next start-up faster. If your Windows XP did not open this feature, open the "Registry Editor" to find [HKEY_LOCAL_MACHINE \ SOFTWARE \ Microsoft \ Dfrg \ BootOptimizefunction], in the right pane, right-click Enable value in the pop-up menu, select "Amendment" and then changed to the value of Y (open) (N for the closure). After the closure of the amendments to the "Registry Editor" and restart the computer. 24, why start win2000 normal, and winxp can not start My computer system with three windows98, widows2000, windows xp were installed in the C, D, E Disk (C disk is FAT32, D, E is NTFS), usually the default E is set to start the windows xp. Before the operation has been normal, Recently, the power-on self test successfully passed, after which the screen black, can not start, the boot is so repeatedly, sometimes success is also occasionally start 3 - 5 minutes to complete the start, before the normal time ghost Backup recovery, xp be able to start the normal 5 - 6 times in the future there is a smooth power-on self test is passed, since black screen or will not boot, the boot is so repeatedly, sometimes success is also occasionally start 3 - 5 minutes to start完成. Later, with windows2000 boot, everything will be all right. Why? A: I was re-install windows xp, running everything will be all right. But I start the computer with windows 2000, windows xp use your computer can not start a normal situation occurred, I found this: This is the windows2000 as a result of clashes with windows xp, I have a computer at the same time with windows xp and windows 2003 there were such cases. It can be seen at the same time with two of the NT system, the installation is complete long as it does not start the previous system, after the installation of a system can be said to be a normal start, but once a pre-installed systems, re-start after a The system will be in conflict, so that after the installation of the system can not start, of course, a pre-installed system can be activated to normal. Concluded: a computer can not install two NT systems. If you want to install both systems, it can only be windows 98/windows xp or windows 98/windows 2000 or windows 98/windows 2003. In addition windows xp can not start for another reason: windows xp, as long as the hard drive in the district have a Bad Track, the system may not be the district where the damage, windows xp can not start. Windows2000 For example, damage to other districts, as long as its not a system where the damage to the district, still be able to start normal. Therefore, windows xp can not start, hard to check whether there are Bad Track, where Bad Track, Bad Track can be hard to repair tool to repair HDD Regenerator v1.41, generally fixed. 25, windows of the input tray gone, how do? Answer: windows of the taskbar disappear input to input Chinese characters into the problem and to solve the problem depends on the circumstances: a, if the windows taskbar input method program (windows xp is: windowssystem32ctfmon, win98/win2000 is: windowssysteminternat.exe) damage, then the only other from computer to copy the program or re-system, the problem is solved. b, if the windows taskbar input method program is not broken, do not just run it, then they would have to run it (as follows), the problem is solved. windows98, windows xp: running enter: msconfig start to determine the appropriate procedures for checking the name. c, if the windows taskbar input method program has been able to function properly, not only in the taskbar display, in accordance with the following operational problems can be solved. windows98: Check the control panel input method "to start on the task bar indicator." windows xp: Control Panel, Regional and Language Options language Language column for more information check "on the desktop display language column" and "in the task bar icon in other languages."